Monthly Archives: February 2012

Learn How to Remove Door Panel on a 2007 Chevy Cobalt LS

Posted on by
Reply

How to Remove Door Panel on a 2007 Chevy Cobalt LSthumbnail

To Remove Door Panel on a 2007 Chevy Cobalt LS, you have to pry around the perimeter of the upper door trim extension with a flat-head screwdriver to disengage its retaining clips. You need to remove the trim panel. After that, remove the screw cover inside the door panel pull cup with prying it out with a flat-head screwdriver. You must remove the two screws securing the pull cup using a Phillips screwdriver. You should lift the cup from the door panel to remove it.

Then, Find the screw cover on the inside door handle and pry it from the bezel with a flat-head screwdriver to expose the handle’s retaining screw. You can remove the retaining screw with using a Phillips screwdriver. Next, Pry the inner door handle assembly away from the door panel with using a flat-head screwdriver and pull it away from the door until you can access the cable on the rear of the handle. You have to pry upward on the connector on the end of the cable to disconnect it from the door handle. You need to remove the door handle from the door panel.

Continue reading →

Learn How to Take the Door Panel off a 1998 Ford F-150

Posted on by
Reply

How to Take the Door Panel Off a 1998 Ford F-150thumbnail

To Take the Door Panel off a 1998 Ford F-150, you have to Open the F-150′s door and close the window completely. You need to Pry the inside door handle bezel loose using the trim tool. You must Pull the bezel off the inside door handle and set it aside. After that, Pry the power lock and window switch bezel off the door panel using the trim tool. You should Reach underneath the bezel and disconnect the wiring harness from the switch by releasing the lock tabs with your thumb and pulling the harness connector away from the switches.

You can set the bezel aside. Then, Remove the door panel retaining bolt exposed when you removed the switch bezel with using a socket wrench and 8-mm socket. You have to remove the screws along the bottom of the door panel using a Phillips screwdriver. Next, Grab the door panel by the inner armrest and lift up until the door panel clears the door. You need to pull the door panel far enough away from the door for you to reach behind it and disconnect the courtesy light wiring harness and speaker wires if applicable.

Continue reading →

Learn How to Install a Stereo in a 2007 Subaru WRX

Posted on by
Reply

How to Install a Stereo in a 2007 Subaru WRXthumbnail

To Install a Stereo in a 2007 Subaru WRX, you have to wrap the tip of a flat head screwdriver with a layer of duct tape to prevent damage to your WRX’s trim panels. After that, Open the WRX’s hood and loosen the nut on the negative battery cable’s pinch bolt. You need to Pull the negative battery cable from the battery and set it aside to prevent accidental reconnection. Then, Pry around the perimeter of the console front panel, the trim panel surrounding the gear shifter and ashtray with using a flat head screwdriver to disengage its five hook pawls. You must remove the console front panel.

Next, remove the two screws at the base of the center panel, the panel surrounding the radio and heating and air-conditioning control panel using a Phillips screwdriver. You should pry outward on the top left and right corners to disengage the two hook pawls using a flat head screwdriver and pull the center panel outward to access the wiring on its rear. Forth, unplug the wiring harnesses from the rear of the center panel and remove the center panel. After that, remove the six screws securing the radio-and-pocket assembly with using a Phillips screwdriver. Then, Press and hold the unlocking buttons on the wiring harnesses on the rear of the radio and unplug the harnesses.

Continue reading →

Learn How to Change Brake Pads on 2004 Chev Malibu

Posted on by
Reply

How to Change Brake Pads on 2004 Chev Malibuthumbnail

To Change Brake Pads on 2004 Chev Malibu, you have to Open the hood of the Malibu. You need to check the brake-reservoir fluid level. If the brake fluid is already at the “Full” mark, you must remove brake fluid with a turkey baster or siphon until the fluid is about 1/2-inch below the “Full” mark. If the fluid level is already below the full mark, you should disregard this step and proceed to loosen the front wheel lug nuts with a tire iron. You can lift the front of the Malibu with a jack.

You have to place jack stands beneath the front frame rails. You need to Lower the car onto the jack stands carefully. You must remove the wheel lug nuts completely with the tire iron and remove both front wheels. You should spin one lug nut onto the face of the rotor on either side of the car to hold the rotor in place during the replacement of the brake pads. Then, Insert a small pry bar into the opening on the outer body of the brake caliper.

Continue reading →

Learn How to make your Hood Black

Posted on by
Reply

How to Make Your Hood Blackthumbnail

To make your Hood Black, you have to find the color code of the black that you want. After that, Test the paint color on an old fender that you have changed out. You need to allow it dries and make sure it turns out to be the black that you want. You must see how many times it takes you to paint over the section until it actually covers. Then, Add 20 percent to the number of coats it took for the color that you chose.

Next, Wash the hood and remove any loose dirt. You should remove the front fender and headlights to avoid getting paint on them. Forth, Remove the hood and lay it out on a table away from other items that could potentially get paint on them. If you cannot remove the hood, you can cover the areas surrounding the hood with painter’s tape. You have to protect your windshield, side panels, headlights and engine from paint.

Continue reading →

Learn How to Make Diesel Engines Run Cooler

Posted on by
Reply

How to Make Diesel Engines Run Coolerthumbnail

To Make Diesel Engines Run Cooler, you have to retune your computer to run at a leaner air/fuel ratio. After that, install a complete exhaust system running from the turbo to the catalytic converter and from the catalytic converter to the tailpipes. Then, buy and install a quality air-to-air intercooler or install a larger-than-stock intercooler if you already have one. Next, inject your engine with water, a 50/50 mix of water and methanol or propane.

Learn How to Change a 2003 Mustang Cobra Taillight

Posted on by
Reply

How to Change a 2003 Mustang Cobra Taillightthumbnail

To Change a 2003 Mustang Cobra Taillight, you have to raise the rear deck lid on the Mustang. You need to Remove the fasteners from the trunk liner and pull the trunk liner inward, away from the rear taillamp assembly. You must remove the four taillamp mounting nuts from the inside of the trunk with using a ratchet and socket. You should pull the rear taillamp assembly outward enough to access the wiring on the taillamp bulbs. After that, turn the bulb socket counterclockwise for the bulb that you are going to replace.

If you are replacing all of the taillight bulbs, you can remove and replace each bulb individually. You have to remove the old bulb from the socket by hand. Then, Wrap the new taillight bulb in a paper towel or clean rag. You need to Install the bulb into the socket and be careful not to touch the bulb lens with your bare hands. You must Push the bulb into the socket and install the socket back into the taillight assembly.

Continue reading →

Learn How to Become an Auto Insurance Collision Appraiser

Posted on by
Reply

How to Become an Auto Insurance Collision Appraiserthumbnail

To Become an Auto Insurance Collision Appraiser, you have to Graduate high school or obtain a GED certificate. After that, get a certificate for mechanical work or mechanical inspection through a vocational school. Then, develop a working knowledge of computers and software programs. Next, get a driver’s license and maintain a good driving record. Forth, Contact the licensing and permits department in your state and complete an application for a collision appraisers license.

Last, apply for an open position as an appraiser with an auto insurance provider.

Where to get cheap auto insurance

Posted on by
Reply

Buying Auto Insurance

To get cheap auto insurance, you can visit kelley book site. On kelley blue book web, you can receive the auto insurance quotes so that you can find out the cheapest insurance that is available today. To use the kelley blue book website, you only have to enter your zip code on the space provided and click get quotes. The kelley blue book site offered the free car insurance quotes. I also used the kelley blue book web to know the auto insurance with the best rate. Each auto insurance may offer different coverage and each individual may need different coverage. So, it is a good idea to decide your needs for coverage in advance before you buy the cheap auto insurance.

I also found the cheap auto insurance with the Liability Coverage on kbb website. Actually, the Liability Coverage can be found in two types including bodily injury liability and property damage cover. To claim for the car insurance, you must also fulfill the requirements. To know the details of the requirements, you can directly visit kelley book site. The Kelley Blue Book web works with distributing a want list to car dealers as well as banks. The list includes the types of automobiles that you are interested in buying along with the amount that you are willing to pay for each.