Category Archives: Autos

Learn How to Replace a Wastegate Flapper

Posted on by
Reply

How to Replace a Wastegate Flapper thumbnail

To Replace a Wastegate Flapper, you have to unbolt the Wastegate from the intake and exhaust ports on the turbocharger system to make working on the unit easier. After that, remove the top of the Wastegate carefully. You need to remove it carefully because when the top of the Wastegate is removed, the spring inside the Wastegate will lose tension and may fly out of the Wastegate housing. Then, disassemble the Wastegate over a workbench so you do not run the risk of losing parts. Next, reassemble the Wastegate using the new flapper in place of the old.

You should rebuild the unit using only replacement parts offered by the manufacturer of your specific Wastegate.

Learn How to Repaint an Outboard

Posted on by
Reply

How to Repaint an Outboard thumbnail

To Repaint an Outboard, you have to Remove the engine cover from the outboard and set it aside nearby. You need to remove the propeller. You must Cover the cables and fuel line. After that, spray the engine completely with degreaser. You should let it to rest on the surface for no less than five minutes, but not long enough for the degreaser to dry on the surface.

Then, Spray the engine with the pressure washer attached to your garden hose. You can let the engine to dry before continuing. Next, Remove or mask off any emblems or stickers on the engine or the engine cover. If you are masking off the emblems, you have to do so with using the masking tape. Forth, Wipe the surface of the motor and engine cover with wax and grease remover on a clean rag.

Continue reading →

Learn How to Clear Coat Rims

Posted on by
Reply

How Can You Clear Coat Rims? thumbnail

To Clear Coat Rims, you have to loosen the lug nuts on all four wheels. You need to Slide the jack under the front axle of the vehicle. You must jack it up and removing both front wheels. You should Place a jack stand behind each wheel hub to support the front of the vehicle as you jack up the back and remove the rear wheels. You can set a jack stand behind each rear wheel hub to keep the vehicle supported when you add a clear coat to the rims.

After that, Take the wheels to a tire shop and ask a professional to remove the tires from the rims. Then, Set your rims on a flat well-ventilated work surface and add two oz. of car soap to a bucket filled with water. You have to dip your brush in the soap. You need to gently scrub each of your rims to remove brake dust and grime that have accumulated on the surface. You must Rinse it with using water from your hose and let the rims to air-dry.

Continue reading →

Learn How to Repair Volvo R60 Headlight Adjuster

Posted on by
Reply

How Do I Repair Volvo R60 Headlight Adjuster? thumbnail

To Repair Volvo R60 Headlight Adjuster, you have to open the Volvo’s hood. You need to Use a socket wrench as well as crescent wrench to disconnect the headlight assembly. You must unplug the headlight from the electrical sockets. You should remove the headlight by pulling it forward. After that, pull the top adjuster bolt out by pushing it up.

You can find the horizontal adjuster on the side of the headlight cavity. You must pull it out with pliers. Then, Insert a flat head screwdriver into the various metal clips holding the glass part of the headlight together with plastic backing. You have to pry these clips to an “open” position. You need to Catch the clip once it pops off and place it in a cup so as not to lose it.

Continue reading →

Learn How to Switch to Electric Transportation

Posted on by
Reply

How do I Switch to Electric Transportation? thumbnail

To Switch to Electric Transportation, you have to consider mass transit. After that, look into electric motorcycles and electric scooters. Then, Research federal tax credits designed to help offset the purchase of an electric car. Next, look for state and local initiatives that reward those who use electric transportation. Forth, consider ride sharing.

Learn How to Paint Vans

Posted on by
Reply

How to Paint Vans thumbnail

To Paint Vans, you have to remove the trim from the van, as well as the side mirrors, front as well as rear bumper and the luggage rack from the roof if equipped. You need to remove the front grill and headlights and the rear tail lights. On full-size vans, you must remove the rear ladder and spare tire. You should remove the door handles, fender flares and running boards. After that, Wash the van thoroughly with soap and water.

You can let it to dry completely. You have to Wet a clean rag with wax and grease remover and clean all the surfaces of the van. As you wipe the wet rag across the surface of the van, you need to remove the wax and grease remover using a clean and dry rag. Then, Mask off the van’s windows as well as the wheels and tires with using the masking tape and masking paper. You must completely cover with masking tape or paper any surface that is not to be painted.

Continue reading →

Learn How to Paint an Avalanche

Posted on by
Reply

How to Paint an Avalanche thumbnail

To Paint an Avalanche, you have to remove all the trim and lower body cladding from the vehicle using the Chevrolet trim-removal tool. You need to avoid using screwdrivers as these will damage the vehicle’s surface. Once the trim is removed, you must use the screwdrivers and socket set to remove the bumpers, grill, headlights as well as taillights, running boards, Tonneau cover, side mirrors, fender flares and the bed trim. After that, Clean the truck using plain soap and water, then allow it to dry completely while you check for spots on the truck that might need repair prior to paint. You should Use spot putty to fill these areas, sand down imperfections and smooth out the surface of the spot putty with using 400-grit sandpaper on a sanding block.

Then, Wipe the surface of the truck using wax and grease remover applied to a clean rag. Next, prepare the surface of the truck with scouring the surface of the paint with a red or gray automotive scratch pad. Once it is completed, you can wipe the truck down again with the wax and grease remover. Forth, Move the truck into a paint booth and mask off the areas that are not to be painted. You have to Prop open the hood of the truck as well as the doors and tailgate.

Continue reading →

Learn How to Paint With Waterborne Three-Stage Paint

Posted on by
Reply

How to Paint With Waterborne Three-Stage Paint thumbnail

To Paint with Waterborne Three-Stage Paint, you have to Tape six spray-out cards to a piece of board and wipe them thoroughly with a tack cloth. You need to apply a coat of self-etching primer to every spray-out card and leave to cure for five minutes before applying two full applications of ground coat. You must leave the ground coat to cure for ten minutes before adding two full coats of waterborne pearl paint color. After that, Remove one spray-out card from the board, write the number “2″ on the back with using a permanent marker to signify that two coats of paint have been applied and put it to one side. You should add another coat of waterborne pearl paint color to the remaining five spray-out cards.

You can remove another single card and write the number “3″ on the back to signify that three coats of color have been applied. You have to continue re-coating and removing one spray-out card at a time until the sixth one is finished. You need to remember to add sequential numbers on the back of each spray-out card after each coat. Then, apply two full applications of clear coat to all six spray-out cards and leave to dry. You must Mask, degrease as well as tack the vehicle before offering the spray-out cards up to the panel to see which one provides the best color match.

Continue reading →

Learn How to Use Metal Flake Paint

Posted on by
Reply

How to Use Metal Flake Paint thumbnail

To Use Metal Flake Paint, you have to Mix the paint thoroughly and pour it into the spray gun’s paint reservoir. You need to plug the air line into the spray gun’s air inlet fitting that leads from the air compressor. You must dial in the paint gun air pressure to twenty pounds per square inch and the spray pattern you want. After that, apply two coats of the metallic paint onto the car. You should let the paint to tack up for five minutes between coats, but do not let it dries altogether.

Then, Turn up the air pressure on the spray gun by 1/4 turn. Next, spray the final coat of paint haphazardly with the paint billowing in clouds over the vehicle. You should ensure to cover the entire surface of the vehicle when standing back slightly further than you would painting in lines. You can Work quickly and empty the remainder of the paint in the paint gun onto the surface of the vehicle. Forth, apply clear top coat and let it to dry for a few days.

Learn How to Repaint a Tractor

Posted on by
Reply

How to Repaint a Tractor thumbnail

To Repaint a Tractor, you have to remove any decals on your tractor with using a putty knife and adhesive remover. After that, remove old paint and rust using 80-grit sandpaper on an orbital sander. Then, Sand other areas of the tractor using 350-grit sandpaper. Next, cover any areas that are not being painted with using the painter’s tape. Forth, Paint the tractor with using a lacquer based primer first and let the primer dry.

After that, apply vehicle paint to the tractor once the primer is dry. You need to Start with a light coat of paint and let this coat to dry. Then, add two additional coats of paint and add heavy coats. You must allow the final coat dry for two days before using the tractor.